PLAMCOR®-3

Fire protection of metal structures exposed to the moderate, moderately cold and cold weather, all atmosphere types and location categories according to GOST 15150 including open-air industrial atmosphere.

It is used as top coat or undercoat in the integrated protective coating systems intended for protection of metal structures from corrosion and fire. It is applied onto the primer coatings ZINEP, ISOLEP-primer, ISOLEP-mastic, GF-021 or other primer coatings on the agreement with the manufacturer.

As topcoats may be used POLYTON-UR (UV), VINICOR-62, ALISTERUS 3105 or another polyurethane, epoxy-vinyl or other topcoats on the agreement with the manufacturer.

Certification

State registration certificate RU.66.01.40.015.E.000356.12.12 dated 12.12.2012;

Conformity certificates № НСОПБ.RU.ЭО.ПР.179.Н.00421 dated 09.02.2022, № ЕАЭС RU C-KZ.HE46.B.00008/23 dated 11.10.2023, № ОГН9.RU.1105.B00008 dated 23.12.2022 (INTERGAZSERT).

Conformity certificate № РОСС RU.AM05.Н13012 dated 29.04.2022, Expert Report by Moscow State Construction University (seismic resistance).

Technical data

Composition

Surface Preparation

Preparation of metal structures

The primer coating shall be cleaned from dirt, dust and decreased, shall be free from moisture and shall not have any corrosive degradation, flaking and cracking, all damaged segments shall be resurfaced.

Preparation of reinforced concrete structures

The surface must be uniformly rough and free

Application

Preparation for use:

• mix thoroughly until homogeneous using mixer;

• when mixing add the hardener (mixing ratio 100:12 by weight, 6.4:1 by volume), after mixing the composition is ready for use. After mixing, the composition is ready for use. The pot life is 1.5 hours at (20±2)°C, when the temperature increases to plus 40°C, it is reduced to 0.5 hours.

• if required prior to application dilute with thinner until working consistency.

The composition shall be applied at temperature from minus 5 to plus 40 °C and relative air humidity of up to 80 %.

PLAMCOR-3 shall be applied in 1-5 layers depending on the fire rating requirements and reduced metal thickness by airless spraying with a wet layer thickness of 900-1100 microns each, while the dry layer thickness will be from 800 to 1000 microns. Natural atmospheric drying.

The maximum holding time of PLAMCOR-3 coating before application of the topcoats is not more than 1 month. The coating is repairable.

Service life of the coating

PLAMCOR-3 as part of a complex coating with a primer and topcoat has a service life of at least 20 years when used in an open atmosphere of moderately cold and cold climates according to GOST 15150. The coating maintains fire protection efficiency for the specified period in the absence of mechanical damage and constant moisture condensation. After the expiration of the specified period, the fire protection coating is subject to replacement with complete removal of the existing layer and its subsequent restoration.

Storage and handling

PLAMCOR-3 composition is two-package: basis and hardener packing in metal buckets.

Storage and transportation are carried out in accordance with GOST 9980.5 (in closed premises, ambient temperature from minus 35 to plus 35 °C). The composition shall be stored far away from the heat sources. During storage avoid direct sunlight and precipitation.

Warranty storage period in air-tight original manufacturer’s containers is 24 months from the date of manufacture.

Precautions

When working with the composition one shall observe the respective industry-specific regulations and norms and protective measures on the package label.

One shall use individual protective equipment (goggles, face shields, respirators); avoid breathing of the solvent vapor and contact of the composition with skin, mucosa of the eyes and respiratory tract.

In case of indoor use sufficient ventilation is required. The composition is classified as fire-hazardous material.

The information is of general character, without consideration to the object specific nature. Use of materials for other purposes not specified here or in case other influencing factors are present shall be approved by the VMP Holding CJSC in writing. In case of absence of such approval the manufacturer is not held liable for the improper use of the material and the buyer falls from the right to present claims connected with the coating quality.

  Technology of application of fire-protective composition PLAMKOR-3.